View ENH057Q1-XXX_1237353.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

White Electronic Designs Display Systems Division
GENERAL DESCRIPTION
Panelview provides optically enhanced solutions to the standard Sharp LQ057Q3DC02 color active matrix LCD module. The first enhancement is an index matching (IM) film lamination to the front surface of the display polarizer. The IM film is available in two surface treatments - IM/Clear and IM/110 (a 10% diffusion).The second enhancement is the incorporation of a reflective polarizer (RP) to improve brightness by up to 40%. The third enhancement is the addition of prism films (RPp) further increasing the brightness of the display. The module is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a backlight unit. Graphics and text can be displayed on a 320 X 3 X 240 dot panel with 262, 144 color by supplying 18 bit data signal (6bit/color), four timing signals.
ENH057Q1-350/450/600
ENH057Q1-350/450/600 Color TFT-LCD Module Features
The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation type. Therefore, this module is also suitable for multimedia use. Viewing angle is 12 o'clock direction. This module is the type of wide viewing angle and high brightness 350cd/m2. It has horizontal display mode and vertical display mode. Backlight-driving DC/AC inverter is not built in this module. Panelview assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. Panelview does assume the responsibility for the warranty of the enhanced product.
MECHANICAL SPECIFICATIONS
Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions (1) Mass Surface treatment
Note: 1. Excluding backlight cables.
Specifications 14.4 (5.7") Diagonal 115.2 (H) x 86.4 (V) 320 (H) x 240 (V) (1 pixel=R+G+B dots) 0.360 (H) x 0.360 (V) R,G,B vertical stripe Normally white 144.0 (W) x 104.6 (H) x 13.0(D) 220 20 IM/Clear (glossy) or IM/110 and hardcoat 3H
Units cm mm pixel mm mm g -
Note: This measurement is typical, and see Fig. 3 for details.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 1 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
INPUT TERMINALS
TTL-LCD Panel Driving
CN1 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Used connector:08-62 10-033-340-800 (Kyocera Elco Corporation) Symbol GND CK HSYNC VSYNC GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND ENAB VCC VCC R/L U/D V/Q GND I/O I I I I I I I I I I I I I I I I I I I I I I I I -
ENH057Q1-350/450/600
Function GND Clock signal for sampling each data signal Horizontal synchronous signal (Negative) Vertical synchronous signal (Negative) GND RED data signal (LSB) RED data signal RED data signal RED data signal RED data signal RED data signal (MSB) GND GREEN data signal (LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal (MSB) GND BLUE data signal (LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal (MSB) GND Signal to settle the horizontal display position (Positive) +3.3V power supply +3.3V power supply Horizontal display mode select signal L: Normal, H: Left/Right reverse mode Vertical display mode select signal L: Normal, H: Up/Down reverse mode VGA/QVGA mode select signal GND
Remarks
(1)
(2) (3)
Note: 1. The horizontal display start timing is settled in accordance with a rising timing of ENAB signal. In case ENAB is fixed "Low", the horizontal start timing is determined as described in "Backlight Driving: on p.5. Don't keep ENAB "Low" during operation.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 2 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
ENH057Q1-350/450/600
WEDC
R/L= L, U/D=H
CDEW
R/L= H, U/D= H
R/L= L, U/D=L BACKLIGHT DRIVING
CN2 Used connector: BHR-2(8.0)VS-1N (JST) Corresponding connector: SM02(8.0)B-BHS-1N-TB Pin No. 1 2 3 Symbol VLOW NC VHIGH (JST)
R/L= H, U/D= L
(installed on a board.) Color of Cable White Red
Function Power supply for lamp (Low voltage side) This is electrically opened Power supply for lamp (High voltage side)
ABSOLUTE MAXIMUM RATINGS
Parameter Input voltage +3.3V supply voltage Storage temperature Operating temperature (Panel) Operating temperature (Ambient) Symbol VI VCC tSTG Topa1 Topa2 Condition tA=25C tA=25C Ratings -0.3~ + 6.0 0~ + 4.0 -30~ + 80 -10~ + 70 -10~ + 70 Unit V V C C C Remark (1) (2) (2, 3, 4) (5)
Notes: 1. CK, RO~R5, G0~G5, B0B5, HSYNC, VSYNC, ENAB, R/L, U/D, V/Q. 2. No parameter is allowed to exceed the range on the surface of the display. 3. Maximum wet-bulb temperature at 39C or less. No dew condensation. 4. Only operation is guarantgeed at operating temperature. Contrast, response time, another display quality are evaluated at =25C. 5. The ambient temperature, when backlight is on. (Reference)
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 3 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
WEDC
CDEW
White Electronic Designs Display Systems Division
ELECTRICAL CHARACTERISTICS
TFT-LCD PANEL DRIVING
+3.3V Parameter Supply voltage Symbol VCC ICC VRF VIL VIH IOL1 IOH1 IOH2 MIN +3.3 0 0.7VCC TYP +3.3 130 MAX +3.6 160 100 0.3VCC +5.5 10 10 100
ENH057Q1-350/450/600
Unit V mA mVp-p V V A A A
Remarks (1) (2) VCC=+3.3V (3) VI=0V (3) VI=3.3~5.0V (4) VI=3.3~5.0v (5)
3.0V
Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (Low) Input current (High)
Notes: 1. VCC-turn-on conditions 0 < t1 < 20ms 0 < t2 < 50ms 0 < t3 < 1s
3.0V 0.3V
Vcc
data
t1
t2
t3
VCC-dip conditions VCC-dip conditions should also follow the VCC-turn-on conditions td < 20ms
Vcc
td
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 4 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
2.4V
3.0V
White Electronic Designs Display Systems Division
2. VCC=3.3V V/Q= "H" Typical current situation Maximum current situation
ENH057Q1-350/450/600
:64-gray bar pattern Timing: Typical signal :Vertical stripe pattern by GS0 and GS42 signal on every other pixel. (This pattern is used temporarily) Timing: Typical signal
GSO GS1 GS2
GS62 GS63
GS42
GS0
Typical Current Situation
Maximum current situation
3. 4. 5.
CK, RO~R5, GO~G5, BO~B5, HSYNC, VSYNC, ENAB, R/L, U/D, V/D CK, RO~R5, GO~G5, BO~B5, HSYNC, VSYNC, R/L, U/D ENAB, V/D
BACKLIGHT DRIVING SECTION
The backlight system is an edge-lighting type with single CCFT (Cold Cathode Fluorescent Tube). The characteristics of a single lamp are shown below.
Parameter Lamp Voltage Lamp current Lamp power consumption Lamp frequency Kickoff voltage tA=25C tA=30C Symbol VL7 IL WL FL VS MIN 620 4.5 30 TYP 690 5.0 3.5 MAX 760 5.5 60 1350 1470 Unit Vrms mArms W KHz Vrms Vrms
tA=25C
Remark IL=6.5mArms normal operation (6) Sealed is connected to GND
(Inverter: HIU-288 [Output Condenser 22pF] Harison Electric Co., LTD.)
6. Lamp frequency may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. Therefore, lamp frequency shall be detached as much as possible from the horizontal synchronous frequency and from the harmonics of horizontal synchronous to avoid interference. In case of such usage under lower temperature environments, periodic lamp exchange by Panelview is recommended.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 5 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
TIMING CHARACTERISTICS OF INPUT SIGNALS
Timing diagrams of input signal are shown below.
ENH057Q1-350/450/600
TIMING CHARACTERISTICS
Clock Parameter Clock Frequency Duty ratio Set up time Hold time Cycle Symbol 1/Tc TH/T Tds Tdh TH TH Pulse width Cycle THp TV TVp THd THc TVh TVs Min. 40 5 10 30.0 770 50.0 360 2 515 251 2 320 10 0 34 7
Notes: 1. In case of lower frequency, deterioration of the display quality, flicker, etc. may occur.
Data Horizontal sync. signal
Vertical sync. signal
Pulse width Horizontal display period HSYNC-Clock phase difference HSYNC.-VSYNC. phase difference Vertical sync. signal start position
Typ. 25.18 6.3 50 31.8 800 63.6 400 96 525 262 320 34 7
Max. 28.33 7.0 60 900 450 200 560 280 34 320 Tc-10 TH-THp 34 7
Unit MHz MHz % ns ns s clock s clock clock line line line clock ns ns line line
Reward V/Q=H V/Q=L
V/Q=H V/Q=L
V/Q=H V/Q=L
V/Q=H V/Q=L
HORIZONTAL DISPLAY POSITION
The horizontal display position is determined by ENAB signal. Parameter Set-up time Pulse width HSYNC-enable signal phase difference Enable signal Symbol Tes Tep THe MIN 5 2 44 2 TYP 320 MAX Tc-10 TH-10 TH-664 TH-340 Unit ns clock clock Remark V/Q=H V/Q=L
Notes: 1. When ENAB is fixed at "V/Q=Low", the display starts from the data of C52 (clock) as shown in Fig. 8. 2. When ENAB is fixed at "V/Q=High", the display starts from the data of C104 (clock) as shown in Fig 8.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 6 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
VERTICAL DISPLAY POSITION
ENH057Q1-350/450/600
The vertical display position (TVs) is fixed at the 34th line (V/Q=H) and 7th line (V/Q=L).
Note: 1. ENAB signal is independent of the vertical display position.
INPUT DATA SIGNALS AND DISPLAY POSITION ON THE SCREEN Display position of input data (H, V)
UP
D1, DH1 D1, DH2 D1, DH3
D2, DH1 D2, DH2
D3, DH1
D320, DH1
R
G
B
D1, DH240
D320, DH240
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 7 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
TH
THp
0.3Vcc 0.3Vcc
Horizontal Sync. signal (Hsync) 0.3Vcc
0.3Vcc
THc
*Only when enable terminal is fixed "low" Tch Tcl
Tc
0.9V
Clock signal (CK)
0.3Vcc 0.3Vcc 0.3Vcc 0.3Vcc
C1* C2*
C52=(V/Q=L) Clock Count Number
C104=(V/Q=H)
Tds Tdh Number of H-data 1.7Vcc D3 D319 D320
Data signal (R0~R5, G0~G5, B0~B5) D1 0.7Vcc D2 Horizontal invalid data period
Horizontal invalid data period THe Tes 0.7Vcc Tep THd
White Electronic Designs Display Systems Division
Data enable signal (ENAB) TV
TVp
0.7Vcc
0.3Vcc
Vertical Sync. signal (Vsync)
TVh
0.7Vcc Number of vertical count
Horizontal Sync. signal (Hsync)
1st line
2nd line
TVs
34th line (V/Q=H) 7th line (V/Q=L)
TVd
Vertical invalid data period
DH1
DH2
DH3
DH239
DH240
Vertical invalid data period
Data signal (R0~R5, G0~G5, B0~B5)
ENH057Q1-350/450/600
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 8 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
Fig 8. Input signal waveforms
White Electronic Designs Display Systems Division
ENH057Q1-350/450/600
INPUT SIGNALS, BASIC DISPLAY COLORS AND GRAY SCALE OF EACH COLOR
Colors & Grayscale Black Blue Green Cyan Red Magenta Yellow White Black Darker Data signal Gray Scale GS0 GS1 GS2 R0 0 0 0 0 1 1 1 1 0 1 0 R1 0 0 0 0 1 1 1 1 0 0 1 R2 0 0 0 0 1 1 1 1 0 0 0 R3 0 0 0 0 1 1 1 1 0 0 0 R4 0 0 0 0 1 1 1 1 0 0 0 R5 0 0 0 0 1 1 1 1 0 0 0 G0 0 0 1 1 0 0 1 1 0 0 0 G1 0 0 1 1 0 0 1 1 0 0 0 G2 0 0 1 1 0 0 1 1 0 0 0 G3 0 0 1 1 0 0 1 1 0 0 0 G4 0 0 1 1 0 0 1 1 0 0 0 G5 0 0 1 1 0 0 1 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0 B1 0 1 0 1 0 1 0 1 0 0 0 B2 0 1 0 1 0 1 0 1 0 0 0 B3 0 1 0 1 0 1 0 1 0 0 0 B4 0 1 0 1 0 1 0 1 0 0 0 B5 0 1 0 1 0 1 0 1 0 0 0
Gray Scale of Red
Basic Color
Brighter Red Black
Gray Scale of Green
Darker
GS61 GS62 GS63 GS0 GS1 GS2
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Brighter Green Black
Gray Scale of Blue
Darker
GS61 GS62 GS63 GS0 GS1 GS2
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Brighter Blue
GS61 GS62 GS63
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
1 0 1
0 1 1
1 1 1
1 1 1
1 1 1
1 1 1
Notes: 1. 0: Low level voltage 1: High level voltage. 2. Each basic color can be displayed in 64 gray scales from 6 bit data signals. 3. With the combination of total 18 bit data signals, the 262, 144-color display can be achieved on the screen.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 9 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
ENH057Q1-350/450/600
OPTICAL CHARACTERISTICS
tA=25C, VCC=+3.3V
Viewing Angle Range Parameter Horizontal Vertical Symbol
21, 22 11 12
Condition (CR>5)
Contrast Ratio Response Time
Rise Decay Luminance of White Chromaticity of White Lamp Endurance +25C
CRmax r d Y x y -
Best Viewing Angle = 0 IL=5.0mArms
Continuation Operation
Min 60 60 35 60 260 0.263 0.279 40,000
Typ 65 65 40 30 50 350 0.313 0.329 -
Max 60 100 0.363 0.379 -
Unit Deg. Deg. Deg. ms ms cd/m2 hour
Remarks (1)
(2) (3) (4)
(5)
Notes: 1. The inverter was used to evaluate the backlight unit. 2. The measurements were done 30 mins later after switching on the backlight.
Photodetector
(BM-5A: TOPCON)
Parameter Luminance of White IM IM, RP IM, RPp
Min. 260 325 450
Typ. 350 450 600
Max. -
Field=2 400mm
TFT-LCD Module
LCD Panel
Center of the screen
Optical Characteristics Measurement Method
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 10 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
Notes: 1. Definition of viewing angle range:
ENH057Q1-350/450/600
q 11 q 21
Normal line
q 11 q 21
12 o'clock direction
2.
Definition of contrast ratio The contrast ratio is defined as follows: Luminance (brightness) with all pixels white Luminance (brightness) with all pixels black Definition of response time The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white". Contrast Ratio (CR)=
3.
white Photodetector output (Relative Value) 100% 90%
black
white
4.
This shall be measured at the center of the screen. The measurement was done 30 mins later after switching on the backlight. (characteristic of the first stage) Inverter drive frequency: 49 kHz Continuous operation time which doesn't deteriorate the brightness under 50% of the brightness at the beginning. (Condition) IL=5.0 mArms (adjusting the brightness by current)
10% 0%
r
d
time
5.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 11 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
HANDLING PRECAUTIONS
Installing the TFT-LCD module 1. TFT-LCD module has holes at the comer of the reverse side of the module to install. M2.6 tapping screw is recommended. (torque: 0.25 ~ 0.30 N x m) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. Also, make certain to design the cabinet so that the switch does not apply pressure on the module. 2. Be sure to turn off the power supply when inserting or disconnecting the cable. 3. Connect GND of Inverter to the metal sealed case of the module. If the connection is not sufficient, it may cause the following: a) Increasing of noise from backlight. b) Unstable inverter output. c) Partial heating up.
ENH057Q1-350/450/600
NOTICE FOR THE DESIGN OF PRODUCTS
1. Design the product to keep TFT-LCD module from sodium chloride or water. 2. W h e n d e s i g n i n g , c o n s i d e r s u f f i c i e n t E M I countermeasures from LCD module to application.
OTHERS
1. Ultraviolet rays deteriorate Liquid-crystal. Do not leave it in direct sun light or in strong ultraviolet rays. 2. If liquid-crystal is kept below the rated storage temperature the isotropic liquid becomes coagulated and may become permanently damaged. Therefore, it is recommended to keep it at room temperature as much as possible. 3. Kick-off voltage of backlight may be required over rated voltage, due to the leakage current from the lamp cable. 4. If the LCD breaks, liquid-crystal may leak from the panel. Be careful so that it does not enter one's eyes and mouth.
INSTALLATION OF THE TFT-LCD MODULE
Installation Precautions 1. Since the front polarizer is easily damaged, avoid rubbing against anything hard or sharp. Use ionized nitrogen to blow off the particles. If polarizer is soiled, wipe lenses with soft cloth. 2. Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 3. Since TFT -LCD modules consist of glass and refined wires and components, it may break or crack if dropped or bumped on hard surface. Handle with care. 4. Since CMOS LSI is used in this module, use caution with static electricity and make certain one is grounded when handling. 5. Do not use LCD module in the vicinity of corrosive gases such as sulfide or chlorine gases. Polarizer may be deteriorate or cause chemical reaction that can lead 10 short circuits at the terminal points. Do not use material containing sulfide or chlorine articles in the vicinity of LCD module. At high temperature, these compounds produce corrosive gases.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 12 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
PACKING FORM
1. Piling number of cartons 3. Carton size 4. Conditions for storage Temperature Humidity Atmosphere Period Opening of the package :0-40C :6O%RH or less :MAX. 12 pcs. :442 (W) X 390 (D) X 170 (H)mm 2. Package quantity in one carton :MAX. 20 pcs.
ENH057Q1-350/450/600
:Display should not be exposed to harmful gases. :3 months :In order to prevent the LCD module from breakdown by electrostatic charges, control room humidity over 50%RH and one must be grounded when opening the package.
OTHERS
3. Image retention may occur when a fixed pattern is displayed for a long period of time. 4. TFT-LCD drive input and output connector (33 pins Kyocera elco corporation :08.6210-033-340-800) a) Adapted FPC b) Holding power of the terminal c) Durability against inserting and extracting : 0.9 N/pin or over (pulling out each terminal at 253 mm/min) : Double of the beginning data or less
(Difference of the contact resistance after 20 times of inserting and extracting, using adapted FPC.)
Rear View
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 13 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
ENH057Q1-350/450/600
17.0 0.07 0.3 0.05
2R-R0.3 5.0 3.0 4 0.5 0.02 0.35 + 0.04 - 0.03 1 2
Number 1 2 3 4
Note: 1. FPC adapted to Input/Output connector (0.5 mm pitch)
0.5 0.12
3
Name Base Copper layer Cover Layer Support board
Material Polyimide or the same kind of material (25m thickness) Thin copper film (35 m thickness) Solder plating 20m or more Polyimide or same kind of material Polyester, Polyimide or the same kind of material (188 m thickness
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 14 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
CONDITIONS OF RELIABILITY TEST
No. 1 2 3 4 5 6 7 Test items High temperature storage test Low temperature storage test High temperature and high humidity operating test High temperature operating test Low temperature operating test Electrostatic discharge test Shock test (non-operating) Vibration test (non-operating) Conditions tA=80C tA=-30C tP=40C, 95%RH (No condensation) tA=70C tA=-10C 200V, 200pF(O) 1 time for each terminal Max gravity Direction Frequency Sweep: 33.3Hz~400Hz Test period tA=-30C~+80C/100 cycles (0.5h) (0.5h)
ENH057Q1-350/450/600
240h 240h 240h 240h 240h
Lamp endurance is excepted
8
:490m/s2 * 6ms :X, Y, Z 3 minutes for each direction (JIS C0041) :5~57Hz/Vibration width : 0.15mm :58~500Hz/Acceleration:9.8m/s2 :11 minutes :3 hours (1 hour in each direction of X, Y, Z)
9
Heat shock test
Note: 1. The following figure shows the definition of X axis, Y axis, and Z axis.
Z
X
Y
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 15 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
ENH057Q1-350/450/600
OUTLINE DIMENSIONS OF 5.7 TFT MODEL
Screen size (115.2 x 86.4)
Direction of the best viewing angle (12 o'clock)
Screen center 104.6
RGBRG
960H x 240V dots (stripe)
49.4
72 144
4-R3
13
Notes: 1. The tolerance is 0.5 except when specified. 2. The tolerance width of the module excludes warping of the case. 3. CN1 connector: ELCO 08-6210-033-340-800 4. 8L connector: JST BHR-02VS-N 5. Unit: mm
REAR VIEW
CN1
LOW
1
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. September 2003 16 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0

▲Up To Search▲

Price & Availability of ENH057Q1-XXX

	To Download ENH057Q1-XXX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .